Skip to content
  1. Blog
  2. Mixing

MixingMixingEQGetting started

What EQ Is: What to Cut, How Much, and Why

EQ is a volume control for each range of pitch. What you hear in the lows, mids and highs, why to start by cutting rather than boosting, what Q means, and what to try first on a vocal, with concrete frequencies.

Written by the site’s operator3 min read
Graphic equalizer sliders
The numbers underneath (63, 125…) are frequencies. Each slider raises or lowers one band.Photo: Mover85 / CC BY-SA 3.0 / Wikimedia Commons

Talk about mixing and EQ always comes up. But there are so many knobs that it is hard to know where to start.

In a phrase, EQ (equalizer) is a volume control for each range of pitch. Instead of raising or lowering everything, it raises or lowers just the low end, or just one part of the highs.

Frequency guide: what lives where

Pitch is measured in hertz (Hz): smaller numbers are lower, larger are higher. The table is a common mixing guide. Positions shift with each voice and instrument, so always confirm by ear.

RangeApprox.What you hear
Subbelow 60 HzWeight you feel. The bottom of kick and bass; too much makes everything vague
Low60–250 HzBody and size. Bass, kick, the base of a male voice
Low mids250–500 HzWhere muddiness and boxiness build up
Mids500 Hz–2 kHzThe core: what makes a voice or instrument sound like itself
Upper mids2–5 kHzClarity and presence. Where hearing is most sensitive; too much hurts
Highs5–10 kHzSibilance (s and sh), cymbal shimmer
Airabove 10 kHzAir and sheen; a little lift sounds brighter
A guide only. “Mud” sits in different places for a voice and an instrument.

Cut before you boost

Once you start, it is tempting to raise what you want more of. Usually it works better to lower what is in the way.

  • Boosting makes things louder, and louder is easily mistaken for better.
  • In a mix of many parts, each giving way a little lets all of them be heard.
  • Cutting never risks clipping.

Q is how much it takes with it

Most EQ bands have three controls: frequency, amount (dB) and Q. Q sets how wide a range around the frequency moves.

  • High Q (narrow): pinpoint moves, for cutting a harsh peak or a particular ring.
  • Low Q (wide): gentle, broad moves, for making the overall tone a little brighter or darker.

Remember “narrow to cut, wide to shape” and you will rarely go far wrong.

What to try first on a cover vocal

  1. Add a high-pass (low cut). Remove the very bottom the voice does not need (roughly below 80–100 Hz). Air-conditioning rumble and stand thumps disappear. For a deep voice, set it lower.
  2. Trim a little mud. Find where it sounds woolly around 250–500 Hz and lower it by just 2–3 dB.
  3. Look for harsh spots. A sharp peak can hide in 2–5 kHz. Finding harsh frequencies explains how.
  4. Finally, listen with the backing. A voice that sounds perfect solo can sound different in the mix. Always judge with everything playing.

Summary

  • EQ is a volume control for each range of pitch.
  • Lowering what is in the way usually beats boosting.
  • Narrow to cut, wide to shape.
  • Match levels when comparing, and make the final call with the backing.

Next: the compressor, which evens out level. Together with EQ, it is the foundation of mixing.

Tools for this article

Read next

Mixing

Where Does Harshness Live? Finding and Taming Piercing Frequencies

Most piercing sound comes from a very narrow peak somewhere around 2–5 kHz. Why hearing is so sensitive there, how to find the peak by sweeping a narrow EQ, how many spots and how much to cut, and how sibilance differs.

Mixing

What a Compressor Is: Narrowing the Gap Between Loud and Quiet

A compressor turns down only what goes over a set level, evening out the volume. What threshold, ratio, attack, release and make-up gain mean, a starting point for vocals, and the signs of overdoing it.

Mixing

Mastering basics: what happens after the mix

Mastering is the last step: turning a finished mix into something ready for streaming or CD. How it differs from mixing, the order of EQ, compression and limiting, streaming loudness (−14 LUFS, −1 dBTP), export formats, and how to approach a cover.

Mixing

What reverb is: giving a voice a room to sit in

Reverb adds the reflections a room would give a sound. What pre-delay, early reflections and decay time mean, how room, hall and plate differ, why reverb goes on a send, and starting points for blending a cover vocal into a backing track.

Mixing

What a limiter is: a level that is never crossed

A limiter catches anything louder than a set ceiling, instantly, so the track does not clip. How it differs from a compressor, why the ceiling goes at −1 dBTP, what true peak means, and how much limiting is too much.

Mixing

What a maximizer is: making a track louder, and why not too loud

A maximizer raises a track’s overall loudness while a limiter holds the peaks down. How it relates to a limiter, how streaming services even out volume (loudness normalisation), what −14 LUFS means, and the signs of pushing too far.

All articles

Sponsored links