Guide rapide des multi-effets › BOSS GX-100 / GX-10 › Réglages
DEVICE LIBRARY / BOSS / VOL. 04
GX-100 / GX-10What the parameters do and how they act on the sound
Ce qu'un seul réglage fait au son, expliqué bloc par bloc.
Tous les réglages
AIRD PREAMP
Distortion
Compressor
Delay
Réverbération
Wah and pedal
AIRD PREAMP12 entrées
AIRD PREAMP is BOSS's own method, recreating the whole amp down to the response of the circuit and the way its parts act on each other. How the controls behave changes with the type.
Réglages de AIRD PREAMP · 12
À mesure que vous lisez, le dessin se rapproche du réglage décrit.
Allez droit à un réglage depuis la liste numérotée ou depuis le bouton sur le dessin.
GAIN
The amount of amp drive, from 0 to 120. The higher, the more drive.
SAG
How much the sense of compression changes with the power amp's response, from -10 to +10. It corresponds to the supply sagging for an instant when a valve amp is hit hard.
Comment s'en servirRaise it and the attack dips before it rises, for a chewy feel. Lower it to tighten up chugging.
RESO(RESONANCE)
How much the dynamics are affected by the interaction of power amp and speaker, from -10 to +10.
Comment s'en servirIt changes how the low end sounds and how the amp pushes back under the fingers. Set it together with SAG.
LEVEL
The overall level of the preamp.
Comment s'en servirThe official guide warns against raising it too far. It causes clipping further down the chain.
BASS
The low tone control, from 0 to 100.
Comment s'en servirA low end that feels good playing alone is almost certainly too much in a band.
MIDDLE
The mid tone control, from 0 to 100.
Comment s'en servirWhether the guitar cuts through a band is decided almost entirely here.
TREBLE
The high tone control, from 0 to 100.
PRESENCE
The tone above that, in the extreme top, from 0 to 100.
Comment s'en servirWhen the guitar will not cut and raising TREBLE makes it sting, raise this instead: it comes forward without the sting.
BRIGHT
Bright on or off. It is not shown on some types.
GAIN SW
Selects the stage of drive from LOW, MIDDLE and HIGH. Drive increases in that order.
Comment s'en servirEach type is voiced around MIDDLE. Normally MIDDLE can be left as it is.
SOLO SW
Switches to a tone for solos.
SOLO LVL(SOLO LEVEL)
The level when SOLO SW is on.
Fin des réglages de AIRD PREAMP
Distortion7 entrées
The controls of the DISTORTION 1 and 2 blocks. From boosters to fuzz, the layout is the same for every type.
Réglages de Distortion · 7
À mesure que vous lisez, le dessin se rapproche du réglage décrit.
Allez droit à un réglage depuis la liste numérotée ou depuis le bouton sur le dessin.
DRIVE
The depth of drive, from 0 to 120.
TONE
The tone, from -50 to +50.
LEVEL
The level of the effect.
Comment s'en servirDrive raises the level too. Match it here so there is no jump when you step on it.
BOTTOM
The low tone control, from -50 to +50. To the left the low end is trimmed, to the right it is lifted.
DIR MIX
The level of the dry (direct) signal.
Comment s'en servirWhen the low end collapses on fuzz or metal types, mixing in a little dry signal brings the core back.
SOLO SW
Switches to a tone for solos.
SOLO LVL(SOLO LEVEL)
The level when SOLO SW is on.
Fin des réglages de Distortion
Compressor6 entrées
The controls of the COMPRESSOR block. Some are not shown, depending on the type.
Réglages de Compressor · 6
À mesure que vous lisez, le dessin se rapproche du réglage décrit.
Allez droit à un réglage depuis la liste numérotée ou depuis le bouton sur le dessin.
SUSTAIN
The range (the time) over which quiet signals are lifted. The larger it is, the longer the sustain. Not shown on the X-BASS type.
ATTACK
The strength of the attack when the strings are picked.
Comment s'en servirStrong gives a popping grain; gentle blends in naturally.
LEVEL
The level.
TONE
The tone, from -50 to +50.
RATIO
The compression ratio, from 1:1 to INF:1.
Comment s'en servirThe higher the ratio the stronger the compression; at INF:1 it behaves much like a limiter.
DIR MIX
The level of the dry (direct) signal.
Comment s'en servirCompress hard and mix in the dry signal, and the natural attack survives.
Fin des réglages de Compressor
Delay3 entrées
Parameters common to the DELAY 1–4 blocks. Not shown on the TWIST type.
Réglages de Delay · 3
À mesure que vous lisez, le dessin se rapproche du réglage décrit.
Allez droit à un réglage depuis la liste numérotée ou depuis le bouton sur le dessin.
TIME
The delay time, set from 1ms to 2000ms or by BPM.
Comment s'en servirSet to BPM it follows each patch's MASTER BPM automatically. Choose this to lock to the tempo. Where the length would exceed the range, it syncs to a half or a quarter of the cycle.
FEEDBACK
How much of the delayed signal returns to the input. The larger it is, the more repeats.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
Comment s'en servirIt gives the texture of a tape echo, the top end falling away with every repeat. It also helps a delay stay out of the way of the dry signal.
Fin des réglages de Delay
Réverbération11 entrées
The controls of the REVERB block. Some are not shown, depending on the type.
Réglages de Réverbération · 11
À mesure que vous lisez, le dessin se rapproche du réglage décrit.
Allez droit à un réglage depuis la liste numérotée ou depuis le bouton sur le dessin.
TIME
The length of the tail, from 0.1 to 10.0 seconds.
TONE
The tone of the reverb, from -50 to +50.
DENSITY
The density of the tail, from 1 to 10.
E.LEVEL
The level of the reverb.
PRE-DELY(PRE-DELAY)
The time before the reverb begins, from 0 to 200ms.
Comment s'en servirWhen you want more reverb but the outline blurs, raise this and the dry signal stays in front.
LO CUT
The frequency at which the low end begins to be trimmed. At FLAT nothing is trimmed.
Comment s'en servirWhen the tail turns muddy, trimming the low end first tidies it up.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
LO DAMP
How much the low end decays, from -50 to +50.
HI DAMP
How much the top end decays, from -50 to +50.
Comment s'en servirIn a real room the top end decays first. A little of this sounds natural.
MOD RATE
The speed at which the reverb is swept.
MOD DEPT(MOD DEPTH)
The depth of the sweep on the reverb.
Fin des réglages de Réverbération
Wah and pedal7 entrées
The controls of WAH and the pedal effects. Some are meant to be assigned to a pedal.
Réglages de Wah and pedal · 7
À mesure que vous lisez, le dessin se rapproche du réglage décrit.
Allez droit à un réglage depuis la liste numérotée ou depuis le bouton sur le dessin.
WAH TYPE
Selects the kind of wah: CRY WAH (CRY BABY), VO WAH (VOX V846) and others.
PDL POS
The position of the wah pedal.
Comment s'en servirAn item meant to be assigned to an expression pedal or the like.
PDL MIN
The tone with the pedal fully back on the heel.
PDL MAX
The tone with the pedal fully down on the toe.
E.LEVEL
The level of the effect.
DIR MIX
The level of the dry (direct) signal.
CURVE(FOOT VOLUME)
Selects how the level follows the pedal: SLOW1, SLOW2, NORMAL or FAST.
Comment s'en servirFor fine control in volume swells, the SLOW settings are easier to handle.
Fin des réglages de Wah and pedal
GX-100 / GX-10 du Liste des types →
Les noms des paramètres suivent le « GX-100 Parameter Guide » officiel de BOSS (en anglais). Parmi les paramètres communs avec le GT-1000CORE, seuls ceux documentés dans le guide du GX-100 figurent ici. Les explications et les conseils d'utilisation sont propres à ce site, ce ne sont pas des traductions officielles.
Les plages de valeurs et l'affichage dépendent du firmware et du type choisi. En cas d'écart avec l'appareil, c'est l'appareil qui fait foi.