Multi-effects model guide › BOSS GX-100 / GX-10 › Controls
DEVICE LIBRARY / BOSS / VOL. 04
GX-100 / GX-10What the parameters do and how they act on the sound
What a single control does to the sound, explained block by block.
All controls
AIRD PREAMP
Distortion
Compressor
Delay
Reverb
Wah and pedal
AIRD PREAMP12 entries
AIRD PREAMP is BOSS's own method, recreating the whole amp down to the response of the circuit and the way its parts act on each other. How the controls behave changes with the type.
AIRD PREAMP · 12 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
GAIN
The amount of amp drive, from 0 to 120. The higher, the more drive.
SAG
How much the sense of compression changes with the power amp's response, from -10 to +10. It corresponds to the supply sagging for an instant when a valve amp is hit hard.
How to use itRaise it and the attack dips before it rises, for a chewy feel. Lower it to tighten up chugging.
RESO(RESONANCE)
How much the dynamics are affected by the interaction of power amp and speaker, from -10 to +10.
How to use itIt changes how the low end sounds and how the amp pushes back under the fingers. Set it together with SAG.
LEVEL
The overall level of the preamp.
How to use itThe official guide warns against raising it too far. It causes clipping further down the chain.
BASS
The low tone control, from 0 to 100.
How to use itA low end that feels good playing alone is almost certainly too much in a band.
MIDDLE
The mid tone control, from 0 to 100.
How to use itWhether the guitar cuts through a band is decided almost entirely here.
TREBLE
The high tone control, from 0 to 100.
PRESENCE
The tone above that, in the extreme top, from 0 to 100.
How to use itWhen the guitar will not cut and raising TREBLE makes it sting, raise this instead: it comes forward without the sting.
BRIGHT
Bright on or off. It is not shown on some types.
GAIN SW
Selects the stage of drive from LOW, MIDDLE and HIGH. Drive increases in that order.
How to use itEach type is voiced around MIDDLE. Normally MIDDLE can be left as it is.
SOLO SW
Switches to a tone for solos.
SOLO LVL(SOLO LEVEL)
The level when SOLO SW is on.
End of the AIRD PREAMP controls
Distortion7 entries
The controls of the DISTORTION 1 and 2 blocks. From boosters to fuzz, the layout is the same for every type.
Distortion · 7 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
DRIVE
The depth of drive, from 0 to 120.
TONE
The tone, from -50 to +50.
LEVEL
The level of the effect.
How to use itDrive raises the level too. Match it here so there is no jump when you step on it.
BOTTOM
The low tone control, from -50 to +50. To the left the low end is trimmed, to the right it is lifted.
DIR MIX
The level of the dry (direct) signal.
How to use itWhen the low end collapses on fuzz or metal types, mixing in a little dry signal brings the core back.
SOLO SW
Switches to a tone for solos.
SOLO LVL(SOLO LEVEL)
The level when SOLO SW is on.
End of the Distortion controls
Compressor6 entries
The controls of the COMPRESSOR block. Some are not shown, depending on the type.
Compressor · 6 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
SUSTAIN
The range (the time) over which quiet signals are lifted. The larger it is, the longer the sustain. Not shown on the X-BASS type.
ATTACK
The strength of the attack when the strings are picked.
How to use itStrong gives a popping grain; gentle blends in naturally.
LEVEL
The level.
TONE
The tone, from -50 to +50.
RATIO
The compression ratio, from 1:1 to INF:1.
How to use itThe higher the ratio the stronger the compression; at INF:1 it behaves much like a limiter.
DIR MIX
The level of the dry (direct) signal.
How to use itCompress hard and mix in the dry signal, and the natural attack survives.
End of the Compressor controls
Delay3 entries
Parameters common to the DELAY 1–4 blocks. Not shown on the TWIST type.
Delay · 3 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
TIME
The delay time, set from 1ms to 2000ms or by BPM.
How to use itSet to BPM it follows each patch's MASTER BPM automatically. Choose this to lock to the tempo. Where the length would exceed the range, it syncs to a half or a quarter of the cycle.
FEEDBACK
How much of the delayed signal returns to the input. The larger it is, the more repeats.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
How to use itIt gives the texture of a tape echo, the top end falling away with every repeat. It also helps a delay stay out of the way of the dry signal.
End of the Delay controls
Reverb11 entries
The controls of the REVERB block. Some are not shown, depending on the type.
Reverb · 11 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
TIME
The length of the tail, from 0.1 to 10.0 seconds.
TONE
The tone of the reverb, from -50 to +50.
DENSITY
The density of the tail, from 1 to 10.
E.LEVEL
The level of the reverb.
PRE-DELY(PRE-DELAY)
The time before the reverb begins, from 0 to 200ms.
How to use itWhen you want more reverb but the outline blurs, raise this and the dry signal stays in front.
LO CUT
The frequency at which the low end begins to be trimmed. At FLAT nothing is trimmed.
How to use itWhen the tail turns muddy, trimming the low end first tidies it up.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
LO DAMP
How much the low end decays, from -50 to +50.
HI DAMP
How much the top end decays, from -50 to +50.
How to use itIn a real room the top end decays first. A little of this sounds natural.
MOD RATE
The speed at which the reverb is swept.
MOD DEPT(MOD DEPTH)
The depth of the sweep on the reverb.
End of the Reverb controls
Wah and pedal7 entries
The controls of WAH and the pedal effects. Some are meant to be assigned to a pedal.
Wah and pedal · 7 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
WAH TYPE
Selects the kind of wah: CRY WAH (CRY BABY), VO WAH (VOX V846) and others.
PDL POS
The position of the wah pedal.
How to use itAn item meant to be assigned to an expression pedal or the like.
PDL MIN
The tone with the pedal fully back on the heel.
PDL MAX
The tone with the pedal fully down on the toe.
E.LEVEL
The level of the effect.
DIR MIX
The level of the dry (direct) signal.
CURVE(FOOT VOLUME)
Selects how the level follows the pedal: SLOW1, SLOW2, NORMAL or FAST.
How to use itFor fine control in volume swells, the SLOW settings are easier to handle.
End of the Wah and pedal controls
Parameter names follow the official BOSS "GX-100 Parameter Guide" (English). Of the parameters shared with the GT-1000CORE, only those documented in the GX-100 guide are listed. The explanations and the how-to-use notes are this site's own, not official translations.
Value ranges and displays depend on firmware and on the chosen type. Where this differs from the unit itself, the unit is correct.