Guía rápida de multiefectos › BOSS GT-1000CORE › Controles
DEVICE LIBRARY / BOSS / VOL. 03
GT-1000COREWhat the parameters do and how they act on the sound
Qué le hace al sonido un solo control, explicado bloque a bloque.
Todos los controles
AIRD PREAMP
Distortion
Compressor
Delay
Reverb
Wah and pedal
AIRD PREAMP12 entradas
AIRD PREAMP is BOSS's own method, recreating the whole amp down to the response of the circuit and the way its parts act on each other. How the controls behave changes with the type.
Controles de AIRD PREAMP · 12
A medida que lees, el dibujo se acerca al control descrito.
Ve directo a un control desde la lista numerada o desde el mando en el dibujo.
GAIN
The amount of amp drive, from 0 to 120. The higher, the more drive.
SAG
How much the sense of compression changes with the power amp's response, from -10 to +10. It corresponds to the supply sagging for an instant when a valve amp is hit hard.
Cómo usarloRaise it and the attack dips before it rises, for a chewy feel. Lower it to tighten up chugging.
RESO(RESONANCE)
How much the dynamics are affected by the interaction of power amp and speaker, from -10 to +10.
Cómo usarloIt changes how the low end sounds and how the amp pushes back under the fingers. Set it together with SAG.
LEVEL
The overall level of the preamp.
Cómo usarloThe official guide warns against raising it too far. It causes clipping further down the chain.
BASS
The low tone control, from 0 to 100.
Cómo usarloA low end that feels good playing alone is almost certainly too much in a band.
MIDDLE
The mid tone control, from 0 to 100.
Cómo usarloWhether the guitar cuts through a band is decided almost entirely here.
TREBLE
The high tone control, from 0 to 100.
PRESENCE
The tone above that, in the extreme top, from 0 to 100.
Cómo usarloWhen the guitar will not cut and raising TREBLE makes it sting, raise this instead: it comes forward without the sting.
BRIGHT
Bright on or off. It is not shown on some types.
GAIN SW
Selects the stage of drive from LOW, MIDDLE and HIGH. Drive increases in that order.
Cómo usarloEach type is voiced around MIDDLE. Normally MIDDLE can be left as it is.
SOLO SW
Switches to a tone for solos.
SOLO LVL(SOLO LEVEL)
The level when SOLO SW is on.
Fin de los controles de AIRD PREAMP
Distortion7 entradas
The controls of the DISTORTION 1 and 2 blocks. From boosters to fuzz, the layout is the same for every type.
Controles de Distortion · 7
A medida que lees, el dibujo se acerca al control descrito.
Ve directo a un control desde la lista numerada o desde el mando en el dibujo.
DRIVE
The depth of drive, from 0 to 120.
TONE
The tone, from -50 to +50.
LEVEL
The level of the effect.
Cómo usarloDrive raises the level too. Match it here so there is no jump when you step on it.
BOTTOM
The low tone control, from -50 to +50. To the left the low end is trimmed, to the right it is lifted.
DIR MIX
The level of the dry (direct) signal.
Cómo usarloWhen the low end collapses on fuzz or metal types, mixing in a little dry signal brings the core back.
SOLO SW
Switches to a tone for solos.
SOLO LVL(SOLO LEVEL)
The level when SOLO SW is on.
Fin de los controles de Distortion
Compressor7 entradas
The controls of the COMPRESSOR block. Some are not shown, depending on the type.
Controles de Compressor · 7
A medida que lees, el dibujo se acerca al control descrito.
Ve directo a un control desde la lista numerada o desde el mando en el dibujo.
THRESHLD(THRESHOLD)
The level at which compression begins. Above it, the signal is compressed. Shown only on the X-BASS type.
Cómo usarloSet it to suit the input signal.
SUSTAIN
The range (the time) over which quiet signals are lifted. The larger it is, the longer the sustain. Not shown on the X-BASS type.
ATTACK
The strength of the attack when the strings are picked.
Cómo usarloStrong gives a popping grain; gentle blends in naturally.
LEVEL
The level.
TONE
The tone, from -50 to +50.
RATIO
The compression ratio, from 1:1 to INF:1.
Cómo usarloThe higher the ratio the stronger the compression; at INF:1 it behaves much like a limiter.
DIR MIX
The level of the dry (direct) signal.
Cómo usarloCompress hard and mix in the dry signal, and the natural attack survives.
Fin de los controles de Compressor
Delay3 entradas
Parameters common to the DELAY 1–4 blocks. Not shown on the TWIST type.
Controles de Delay · 3
A medida que lees, el dibujo se acerca al control descrito.
Ve directo a un control desde la lista numerada o desde el mando en el dibujo.
TIME
The delay time, set from 1ms to 2000ms or by BPM.
Cómo usarloSet to BPM it follows each patch's MASTER BPM automatically. Choose this to lock to the tempo. Where the length would exceed the range, it syncs to a half or a quarter of the cycle.
FEEDBACK
How much of the delayed signal returns to the input. The larger it is, the more repeats.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
Cómo usarloIt gives the texture of a tape echo, the top end falling away with every repeat. It also helps a delay stay out of the way of the dry signal.
Fin de los controles de Delay
Reverb11 entradas
The controls of the REVERB block. Some are not shown, depending on the type.
Controles de Reverb · 11
A medida que lees, el dibujo se acerca al control descrito.
Ve directo a un control desde la lista numerada o desde el mando en el dibujo.
TIME
The length of the tail, from 0.1 to 10.0 seconds.
TONE
The tone of the reverb, from -50 to +50.
DENSITY
The density of the tail, from 1 to 10.
E.LEVEL
The level of the reverb.
PRE-DELY(PRE-DELAY)
The time before the reverb begins, from 0 to 200ms.
Cómo usarloWhen you want more reverb but the outline blurs, raise this and the dry signal stays in front.
LO CUT
The frequency at which the low end begins to be trimmed. At FLAT nothing is trimmed.
Cómo usarloWhen the tail turns muddy, trimming the low end first tidies it up.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
LO DAMP
How much the low end decays, from -50 to +50.
HI DAMP
How much the top end decays, from -50 to +50.
Cómo usarloIn a real room the top end decays first. A little of this sounds natural.
MOD RATE
The speed at which the reverb is swept.
MOD DEPT(MOD DEPTH)
The depth of the sweep on the reverb.
Fin de los controles de Reverb
Wah and pedal7 entradas
The controls of WAH and the pedal effects. Some are meant to be assigned to a pedal.
Controles de Wah and pedal · 7
A medida que lees, el dibujo se acerca al control descrito.
Ve directo a un control desde la lista numerada o desde el mando en el dibujo.
WAH TYPE
Selects the kind of wah: CRY WAH (CRY BABY), VO WAH (VOX V846) and others.
PDL POS
The position of the wah pedal.
Cómo usarloAn item meant to be assigned to an expression pedal or the like.
PDL MIN
The tone with the pedal fully back on the heel.
PDL MAX
The tone with the pedal fully down on the toe.
E.LEVEL
The level of the effect.
DIR MIX
The level of the dry (direct) signal.
CURVE(FOOT VOLUME)
Selects how the level follows the pedal: SLOW1, SLOW2, NORMAL or FAST.
Cómo usarloFor fine control in volume swells, the SLOW settings are easier to handle.
Fin de los controles de Wah and pedal
GT-1000CORE de Lista de tipos →
Los nombres de los controles y sus rangos siguen la "GT-1000CORE Parameter Guide" oficial de BOSS (en inglés). Las explicaciones y las notas de uso son propias de este sitio, no traducciones oficiales.
Qué controles aparecen depende del firmware y del tipo elegido. Si esto difiere del aparato, manda el aparato.