Guía rápida de FX 日本語

Guía rápida de multiefectos › Line 6 HX Stomp › Controles

DEVICE LIBRARY / Line 6 / VOL. 01

HX StompWhat the parameters do and how they act on the sound

Qué le hace al sonido un solo control, explicado bloque a bloque.

41 CONTROLS6 CATEGORIESSegún Ver.3.80 ↗
06B1Seismic MattersTwinHarmonyAdriaticDelayTAP/TUNER⌂ VIEWACTIONSAVE◀ PAGEPAGE ▶≡VOLUMELINE 6HX STOMPLine 6 HX Stomp

Explore published presets & tone settings ↗

Amplificadores12 entradas

The controls of the Amp, Amp+Cab and Preamp blocks. Bass, Mid, Treble and the row above recreate the circuits of the real amps, so how they act and how they interact differ from model to model. From Master down, they are common to every amp model.

MFGVIRTUAL AMP · A-12CH VOL01010DRIVE02010BASS03010MID04010TREBLE05010PRESENCE06010MASTER07010SAG08010HUM09010RIPPLE10010BIAS11010BIAS X12010INPUTPOWER

Controles de Amplificadores · 12

A medida que lees, el dibujo se acerca al control descrito.

Ve directo a un control desde la lista numerada o desde el mando en el dibujo.

  1. Ch Vol

    Raises or lowers the level alone, without changing the tone. It does not affect the drive.

    Cómo usarloUsed once the tone is set, to match levels between presets. It corresponds to a fader on a mixer.

  2. Drive

    How much is sent into the preamp. The higher, the more drive. On amps with a master volume it acts as gain; on amps without one it is the real amp's volume control itself.

  3. Bass

    The amount of low end. The real circuit is recreated, so on some models the midrange and the drive move with it.

    Cómo usarloA low end that feels good playing alone is almost certainly too much in a band. It is the band closest to the bass, so think in terms of taking it away and the parts fit together.

  4. Mid

    The amount of midrange. Whether the guitar cuts through a band is decided almost entirely here.

    Cómo usarloLower it and the tone scoops. It sounds good alone, but it is behind most cases of a guitar disappearing in a recording.

  5. Treble

    The amount of top end. Raise it for outline and cut. Too far and it stings.

    Cómo usarloOn models with a control the real amp does not have, starting at twelve o'clock (50%) is the honest approach.

  6. Presence

    The tension of the top end at the power amp. It acts above the band of the tone stack's Treble.

    Cómo usarloWhen the guitar will not cut and raising Treble makes it sting, raise this instead: it comes forward without the sting.

  7. Master

    How hard the power amp is pushed. The higher, the more power-valve drive. With this low, Sag, Bias and Bias X all weaken together.

    Cómo usarloOn models of amps without a master volume, 100% is the norm. If moving the controls below has little effect, first check whether Master is too low.

  8. Sag

    The time a valve takes to return to full power after a heavy load. Also called compression or squash, it puts a dip into the attack.

    Cómo usarloRaise it on small tweed amps when you want depth and chew. In country or metal, where fast picking and chord work run on, it blurs the sound, so lower it and tighten up.

  9. Hum

    How much hum leaking from the preamp valve heaters is mixed into the signal. Less a tone control than the rawness and grit of a real amp. Over drive it adds instability.

    Cómo usarloThere is no control for this on the real amp and no right answer. Starting around twelve o'clock (50%) and following your ear is the safe approach.

  10. Ripple

    How much ripple left over from the power supply's rectification is mixed into the signal. With Hum, it sets how worn the amp feels.

    Cómo usarloAs with Hum, there is no matching control on the real amp. Raise it and the drive wavers and turns unstable.

  11. Bias

    The output valve bias. Properly it sets the valves to their best operating point, but it serves tone as well. Higher (hotter) is warmer, softer and easier to drive; lower (colder) has more punch and more headroom.

    Cómo usarloFor hard and tight, go colder; for warm and easily driven, go hotter. If crossover distortion bothers you, raising it to around 6–8 settles it.

  12. Bias X

    The amount of bias excursion — the bias shifting momentarily — in the output stage at high volume and high input. The larger the shift, the more it is heard as crossover distortion.

    Cómo usarloRaise it and crossover distortion appears more readily, with a stronger sense of valves collapsing. It is bound up with Drive and Master, so set it together with them rather than alone. The Line 6 article notes that most players need not concern themselves with this control.

Fin de los controles de Amplificadores

HX Stomp de Lista de modelos →

Se han consultado el "HX Stomp Manual" de Line 6, el artículo de Line 6 Japan (Dave Hunter, "Uso de los ajustes Sag, Bias y Bias Excursion") y la comunidad Helix Help . El texto es propio de este sitio, no una declaración ni una traducción oficial.

Los controles aparecen y desaparecen según el firmware y el modelo. Si esto difiere del aparato, manda el aparato.

Actualizado

Line 6 y HX Stomp son marcas de Line 6 / Yamaha Guitar Group. Los nombres de los productos modelados son marcas de sus respectivos propietarios, ninguno de los cuales guarda relación con este sitio.

Unofficial reference · Not affiliated with Line 6