Guida rapida ai multieffetto › Line 6 HX Stomp › Controlli
DEVICE LIBRARY / Line 6 / VOL. 01
HX StompWhat the parameters do and how they act on the sound
Che cosa fa al suono un singolo controllo, spiegato blocco per blocco.
Tutti i controlli
Amplificatori
Cabinets and IRs
Delay and reverb
Modulazione
Common
Send / Return
Amplificatori12 voci
The controls of the Amp, Amp+Cab and Preamp blocks. Bass, Mid, Treble and the row above recreate the circuits of the real amps, so how they act and how they interact differ from model to model. From Master down, they are common to every amp model.
Controlli di Amplificatori · 12
Man mano che leggi, il disegno si avvicina al controllo descritto.
Vai direttamente a un controllo dall'elenco numerato o dalla manopola nel disegno.
Ch Vol
Raises or lowers the level alone, without changing the tone. It does not affect the drive.
Come si usaUsed once the tone is set, to match levels between presets. It corresponds to a fader on a mixer.
Drive
How much is sent into the preamp. The higher, the more drive. On amps with a master volume it acts as gain; on amps without one it is the real amp's volume control itself.
Bass
The amount of low end. The real circuit is recreated, so on some models the midrange and the drive move with it.
Come si usaA low end that feels good playing alone is almost certainly too much in a band. It is the band closest to the bass, so think in terms of taking it away and the parts fit together.
Mid
The amount of midrange. Whether the guitar cuts through a band is decided almost entirely here.
Come si usaLower it and the tone scoops. It sounds good alone, but it is behind most cases of a guitar disappearing in a recording.
Treble
The amount of top end. Raise it for outline and cut. Too far and it stings.
Come si usaOn models with a control the real amp does not have, starting at twelve o'clock (50%) is the honest approach.
Presence
The tension of the top end at the power amp. It acts above the band of the tone stack's Treble.
Come si usaWhen the guitar will not cut and raising Treble makes it sting, raise this instead: it comes forward without the sting.
Master
How hard the power amp is pushed. The higher, the more power-valve drive. With this low, Sag, Bias and Bias X all weaken together.
Come si usaOn models of amps without a master volume, 100% is the norm. If moving the controls below has little effect, first check whether Master is too low.
Sag
The time a valve takes to return to full power after a heavy load. Also called compression or squash, it puts a dip into the attack.
Come si usaRaise it on small tweed amps when you want depth and chew. In country or metal, where fast picking and chord work run on, it blurs the sound, so lower it and tighten up.
Hum
How much hum leaking from the preamp valve heaters is mixed into the signal. Less a tone control than the rawness and grit of a real amp. Over drive it adds instability.
Come si usaThere is no control for this on the real amp and no right answer. Starting around twelve o'clock (50%) and following your ear is the safe approach.
Ripple
How much ripple left over from the power supply's rectification is mixed into the signal. With Hum, it sets how worn the amp feels.
Come si usaAs with Hum, there is no matching control on the real amp. Raise it and the drive wavers and turns unstable.
Bias
The output valve bias. Properly it sets the valves to their best operating point, but it serves tone as well. Higher (hotter) is warmer, softer and easier to drive; lower (colder) has more punch and more headroom.
Come si usaFor hard and tight, go colder; for warm and easily driven, go hotter. If crossover distortion bothers you, raising it to around 6–8 settles it.
Bias X
The amount of bias excursion — the bias shifting momentarily — in the output stage at high volume and high input. The larger the shift, the more it is heard as crossover distortion.
Come si usaRaise it and crossover distortion appears more readily, with a stronger sense of valves collapsing. It is bound up with Drive and Master, so set it together with them rather than alone. The Line 6 article notes that most players need not concern themselves with this control.
Fine dei controlli di Amplificatori
Cabinets and IRs8 voci
The controls of the Cab and IR blocks. The type of microphone and the distance alone change the impression greatly. Settling these before touching the EQ is the short road.
Controlli di Cabinets and IRs · 8
Man mano che leggi, il disegno si avvicina al controllo descritto.
Vai direttamente a un controllo dall'elenco numerato o dalla manopola nel disegno.
Mic
The type of microphone placed at the cabinet. Twelve types each for guitar and bass cabinets, sixteen for the legacy cabinets. The same cabinet leaves a very different impression with a different microphone.
Come si usaThe 57 family pushes the upper midrange forward: the rock standard. Ribbons are settled and smooth on top. Condensers catch detail well into the top end.
Distanc
The distance from microphone to speaker. Within one to twelve inches: closer lifts the low end (proximity effect), further back reduces it and mixes in a sense of air.
Come si usaWhen there is too much low end, moving back a little settles it naturally, before reaching for the EQ.
Low Cut / High Cut(Cab)
Trims the cabinet's low and high.
Come si usaThe first thing done when miking for real, too. A sluggish low end and a fizzy top are sorted faster by taking away than by adding.
Reflec
The amount of early reflections. The higher, the more it feels played in a room. Less noticeable than reverb — the presence of a space.
Level(Cab)
The output level of the cabinet block.
IR Sel
Selects a loaded IR by number. Up to 128 can be stored in the unit.
Come si usaThe block refers to a number, not to an IR file. Replace what sits at that number in HX Edit and every preset using it changes.
Low Cut / Hi Cut(IR)
Trims the IR's low and high. The thinking is the same as for a cabinet.
Mix / Level(IR)
The proportion of the signal passing through the IR, and the block's output level.
Come si usaMix is normally left at 100%. Lower it and the bare sound, not passing through the IR, is mixed in.
Fine dei controlli di Cabinets and IRs
Delay and reverb7 voci
The controls of delay and reverb. Set the time in note values and it follows when the tempo changes.
Controlli di Delay and reverb · 7
Man mano che leggi, il disegno si avvicina al controllo descritto.
Vai direttamente a un controllo dall'elenco numerato o dalla manopola nel disegno.
Time
The delay interval. Push the knob to switch between ms and note values.
Come si usaSet in note values, the delay follows a change of tempo. A value set as a note is kept when the model is changed.
Feedbk
The number of repeats. The higher, the longer it lingers; at the top it oscillates and swells without end.
Scale
On delays with several taps, it sets where each tap falls as a percentage of Time. With Time at 500ms and Scale at 50%, that tap is at 250ms.
Come si usaMoving Time shifts every tap in proportion, so the shape of the rhythm holds while only the speed changes.
Decay
How long the reverb takes to decay. Short is a room, long is a hall.
Predly
The gap between the dry sound and the start of the tail.
Come si usaWhen you want more reverb but the outline blurs, raise this and the dry signal stays in front.
Spread
The stereo width. On most delays it sets how far the repeats swing left and right (0 in the centre, 10 full width). On stereo delays with modulation it is the offset between the two sweeps, so at 10 one side rises as the other falls.
Trails
What happens to the tail the moment the block is bypassed. Off cuts it instantly; On lets it decay naturally.
Come si usaIf you switch it mid-song, On sounds less abrupt.
Fine dei controlli di Delay and reverb
Modulazione3 voci
The controls of the modulating effects: chorus, phaser, tremolo and the rest.
Controlli di Modulazione · 3
Man mano che leggi, il disegno si avvicina al controllo descritto.
Vai direttamente a un controllo dall'elenco numerato o dalla manopola nel disegno.
Speed
The speed of the sweep. Push the knob to switch between Hz (cycles per second) and note values.
Come si usaNote values to sit with the song, Hz to sweep free of the tempo. On models whose response is non-linear, note sync may not be possible.
Rate
The speed of the sweep, as with Speed. Push to switch between a number and note values.
Depth
The depth of the sweep. Shallow is a light colouring, deep is a clear swell. How it acts is decided together with Speed.
Fine dei controlli di Modulazione
Common5 voci
Controls common to most effect blocks, whatever their kind.
Controlli di Common · 5
Man mano che leggi, il disegno si avvicina al controllo descritto.
Vai direttamente a un controllo dall'elenco numerato o dalla manopola nel disegno.
Drive (effect)
The amount of drive. The higher, the more it collapses. Level and midrange rise with it.
Come si usaAfter adding drive, bring the level back with Level and there will be no jump in volume when you step on it.
Level
The block's output level. Raised too far across several blocks, it clips in the digital domain.
Come si usaUnless you mean to boost, leaving it at 0.0dB is safe.
Low Cut / Hi Cut
Trims the low and high of that block. It sorts a sluggish low end and a harsh top.
Come si usaWhen the guitar will not cut through a band, trimming here often settles it before anything is added.
Mix
The proportion of effect to dry signal. At 0% it passes through; at 100% the dry sound is gone.
Come si usaKeep it low for delay and reverb. 100% is for the kinds, like wah and filters, that leave no dry signal.
Headrm
The headroom inside the block. Negative adds grit, positive tidies it up. At 0dB it behaves as the real unit does.
Come si usaWhen it turns gritty after high-gain drive, moving it positive settles it.
Fine dei controlli di Common
Send / Return6 voci
A block for placing your own pedals anywhere in a preset.
Controlli di Send / Return · 6
Man mano che leggi, il disegno si avvicina al controllo descritto.
Vai direttamente a un controllo dall'elenco numerato o dalla manopola nel disegno.
Send
The level sent out to the external effect.
Come si usaIf it distorts at the destination, or the tone thins instead, match it here.
Dry Thru
The level of the signal passing straight through the Send block. It is set separately from the Send level.
Come si usaNormally left at 0.0dB.
Return
The level of the signal returning from the external effect.
Mix(Return)
The proportion of returned to dry signal. 0% is a complete bypass, 100% is the Return alone.
Mix(FX Loop)
The proportion of the looped signal to the dry one. 0% is a complete bypass, 100% sends everything through the loop.
Come si usaSet to 100% with nothing connected, there is no sound unless the FX Loop block is bypassed. When there is no sound, suspect this first.
Trails(FX Loop)
Whether the tail of an external delay or reverb remains when the loop is switched off.
Come si usaIf you switch it mid-song, On sounds more natural.
Fine dei controlli di Send / Return
HX Stomp di Elenco dei modelli →
Sono stati consultati il "HX Stomp Manual" di Line 6, l'articolo di Line 6 Japan (Dave Hunter, "Usare le regolazioni Sag, Bias e Bias Excursion") e la comunità Helix Help . Il testo è di questo sito, non una dichiarazione né una traduzione ufficiale.
I controlli compaiono e scompaiono secondo il firmware e il modello. Se qualcosa diverge dall'apparecchio, fa fede l'apparecchio.