Multi-effects model guide › BOSS GX-1 › Controls
DEVICE LIBRARY / BOSS / VOL. 05
GX-1What the parameters do and how they act on the sound
What a single control does to the sound, explained block by block.
All controls
AMP
Distortion
Compressor
Delay
Reverb
Wah and pedal
AMP5 entries
AIRD PREAMP is BOSS's own method, recreating the whole amp down to the response of the circuit and the way its parts act on each other. How the controls behave changes with the type.
AMP · 5 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
GAIN
The amount of amp drive, from 0 to 120. The higher, the more drive.
LEVEL
The overall level of the preamp.
How to use itThe official guide warns against raising it too far. It causes clipping further down the chain.
BASS
The low tone control, from 0 to 100.
How to use itA low end that feels good playing alone is almost certainly too much in a band.
MIDDLE
The mid tone control, from 0 to 100.
How to use itWhether the guitar cuts through a band is decided almost entirely here.
TREBLE
The high tone control, from 0 to 100.
End of the AMP controls
Distortion4 entries
The controls of the DISTORTION 1 and 2 blocks. From boosters to fuzz, the layout is the same for every type.
Distortion · 4 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
DRIVE
The depth of drive, from 0 to 120.
TONE
The tone, from -50 to +50.
LEVEL
The level of the effect.
How to use itDrive raises the level too. Match it here so there is no jump when you step on it.
DIR MIX
The level of the dry (direct) signal.
How to use itWhen the low end collapses on fuzz or metal types, mixing in a little dry signal brings the core back.
End of the Distortion controls
Compressor5 entries
The controls of the COMPRESSOR block. Some are not shown, depending on the type.
Compressor · 5 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
THRESHLD(THRESHOLD)
The level at which compression begins. Above it, the signal is compressed. Shown only on the X-BASS type.
How to use itSet it to suit the input signal.
SUSTAIN
The range (the time) over which quiet signals are lifted. The larger it is, the longer the sustain. Not shown on the X-BASS type.
ATTACK
The strength of the attack when the strings are picked.
How to use itStrong gives a popping grain; gentle blends in naturally.
LEVEL
The level.
RATIO
The compression ratio, from 1:1 to INF:1.
How to use itThe higher the ratio the stronger the compression; at INF:1 it behaves much like a limiter.
End of the Compressor controls
Delay3 entries
Parameters common to the DELAY 1–4 blocks. Not shown on the TWIST type.
Delay · 3 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
TIME
The delay time, set from 1ms to 2000ms or by BPM.
How to use itSet to BPM it follows each patch's MASTER BPM automatically. Choose this to lock to the tempo. Where the length would exceed the range, it syncs to a half or a quarter of the cycle.
FEEDBACK
How much of the delayed signal returns to the input. The larger it is, the more repeats.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
How to use itIt gives the texture of a tape echo, the top end falling away with every repeat. It also helps a delay stay out of the way of the dry signal.
End of the Delay controls
Reverb5 entries
The controls of the REVERB block. Some are not shown, depending on the type.
Reverb · 5 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
TIME
The length of the tail, from 0.1 to 10.0 seconds.
TONE
The tone of the reverb, from -50 to +50.
DENSITY
The density of the tail, from 1 to 10.
PRE-DELY(PRE-DELAY)
The time before the reverb begins, from 0 to 200ms.
How to use itWhen you want more reverb but the outline blurs, raise this and the dry signal stays in front.
HI CUT
The frequency at which the top end begins to be trimmed. At FLAT nothing is trimmed.
End of the Reverb controls
Wah and pedal5 entries
The controls of WAH and the pedal effects. Some are meant to be assigned to a pedal.
Wah and pedal · 5 controls
As you read on, the drawing moves to the control being described.
Jump straight to a control from the numbered list, or from the knob in the drawing.
WAH TYPE
Selects the kind of wah: CRY WAH (CRY BABY), VO WAH (VOX V846) and others.
PDL MIN
The tone with the pedal fully back on the heel.
PDL MAX
The tone with the pedal fully down on the toe.
DIR MIX
The level of the dry (direct) signal.
CURVE(FOOT VOLUME)
Selects how the level follows the pedal: SLOW1, SLOW2, NORMAL or FAST.
How to use itFor fine control in volume swells, the SLOW settings are easier to handle.
End of the Wah and pedal controls
Parameter names follow the official BOSS "GX-1 Parameter Guide" (English). Of the parameters shared with the GT-1000CORE, only those documented in the GX-1 guide are listed. The GX-1 amp has only GAIN, BASS, MIDDLE, TREBLE and LEVEL, with no SAG and the like. The explanations and the how-to-use notes are this site's own, not official translations.
Value ranges and displays depend on firmware and on the chosen type. Where this differs from the unit itself, the unit is correct.